S9200U000 Replaces These Integrated Furnace Controls. (Continued) SKU Harness Nordyne D Main B A A B C D A A B 7028A CAR90306 United Technologies A D 02955A Main B Texas Instruments 6DT- A 6DT-2 6F3 Safety Timing Field Settings Settings - Recommendation DIP - DIP Switch S Switch S EF 03 2ģ S9200U000 UNIVERSAL HOT SURFACE IGNITION INTEGRATED FURNACE CONTROL Table. SKU Harness United Technologies A D B Main C C Rheem/ Robert Shaw D Main C Safety Timing Field Settings Settings - Recommendation DIP - DIP Switch S Switch S2 Table.
See Table 2 for replacement details for Trane controls. CROSS REFERENCE IMPORTANT Only use the S9200U000 on 20 Vac e Table for the replacement details for other manufacturers controls. See Safety Timings, Field Settings, and Fixed Parameters beginning on page. See Wiring on page Configure the field settings and safety timings. See Replacement on page Connect the wiring harnesses and make the wiring connections. See Replacement on page Mount the S9200U000 Integrated Furnace Control. Remove old device and carefully identify and mark any wiring. Identify cross reference target using Table.
Flashcode gratuit pour tablette install#
on page 7 Place Bar Code Here EF-03Ģ S9200U000 UNIVERSAL HOT SURFACE IGNITION INTEGRATED FURNACE CONTROL INSTALLATION AND CONFIGURATION OVERVIEW The following is an overview of the steps required to install and configure the S9200U000 Integrated Furnace Control.
Flashcode gratuit pour tablette trial#
INSTALLATION INSTRUCTIONS SPECIFICATIONS Line Voltage: Line 20V (97-32 Vac), 60 Hz Low Voltage: Line 24V (9-30 Vac), 60 Hz Current Draw: 0.5A Input Vac, plus valve 24 Vac plus cooling contactor Igniter Current: 5.0A 32 Vac output Thermostat Anticipator Setting: (Stage only) 00mA Prepurge: 30 seconds Warm-up: 7/27 or 30/30 seconds (st/next trial) depending on DIP switch S2 setting Trial for Ignition: 4, 6, or 8 seconds depending on DIP switch S2 setting Postpurge: 5 seconds Inter-trial Purge: 60 seconds Auto Restart Delay: 60 minutes (after Soft Lockout) Ignition Trials: Three two retries if flame is not sensed on the first trial Flame Failure Response Time: 2 seconds μa LEDs: Three LEDs provide the following: A red LED provides system status and faults An amber LED provides flame status information A green LED provides information about the EnviraCOM traffic Wire harnesses: 2 pin, 3 x 4 connector, 7 inches main harness (2) 4-pin, 4 x connector, 7 inches igniter/inducer harness (5) Jumper wire Fan Delays: Heat Fan ON Delay: 30 or 60 seconds depending on DIP switch S setting Heat Fan OFF Delay: 60, 90, 20, or 80 seconds depending on Dip Switch S setting Cool Fan ON Delay: 5 seconds Cool Fan OFF Delay: 0 or 60 seconds (depending on DIP Switch S setting) Gas Control: Any 24 Vac redundant, direct ignition gas control rated at.5a or less Honeywell VR88345M4320 recommended Cooling Contactor: Any 24 Vac contactor rated at.0a or less Induced Draft Blower: 2.2FLA/3.5LRA 20 Vac Circulator Load: 4.5FLA/25LRA 20 Vac Line Voltage Humidifier: A resistive load 20 Vac Electronic Air Cleaner: A resistive load 20 Vac Replaceable Fuse: 3.0 Amp, Automotive type Operating Temperature: -40 F to 75 F (-40 C to 79 C) Relative humidity: 0% to 95% non-condensing Dimensions: See Fig. EnviraCOM communication capability to enable local and/or remote system status, diagnostics, troubleshooting, and HVAC system control. Wire harnesses provided for simple replacement of most IFCs and integration with most heating and cooling appliances. LED system status, performance and diagnostic indication. Control of a standard induction-type circulating fan motor (based on appliance requirements), in response to a conventional low voltage or EnviraCOM thermostat. Appliance operation/safety requirements controlled via microprocessor. Monitoring of system pressure switch, high temperature limit, and rollout functions. Flame rectification circuit to monitor flame presence. FEATURES The S9200U000 provides: Main burner ignition using a 20V hot surface igniter. The S9200U000 EnvriaCOM communications capability allows its use in twinning applications and enables communication with local and remote diagnostic devices such as the QuickLook hand held device (QuickLook 72), EnviraLNK web-based application and the W8735D Telephone Access Module (TAM). The S9200U000 Universal Integrated Furnace Control is intended for residential natural or liquid propane fueled furnaces only. The S9200U000 can be used with conventional thermostats as well as the EnviraCOM enabled VisionPRO IAQ and FocusPRO. Keyed wire harnesses allow the S9200U000 to replace most furnace controls and to be applied to most heating and cooling single stage appliances. 1 S9200U000 Universal Hot Surface Ignition Integrated Furnace Control APPLICATION The S9200U000 Universal Integrated Furnace Control is a combustion control used in single stage gas heating and cooling appliances.
0 kommentar(er)
